MIXPAC®"S" system offers dispensing of 1:1, 2:1, 3:2, 4:1 and 10:1 volumetric ratios all within 1 dispenser; improved, ergo-nomic design; new-fashioned cartridge design has separate cylinders and a stronger attachment flange to allow for higher dispensing pressures; interface with separated outlets between cartridge and mixer or cap prevents cross contamination and avoids plugged cartridges. ConProTec, Inc. WRITE IN NO. 201

Complete range of connectors, plugs and receptacles; FM rated IP68 to provide complete protection against dust and allow for continuous submersion in up to 6 ft. of water when capped or mated; exceed OSHA and NEMA requirements; suitable for IEC Class IP67 and NEMA Class 6 applications; available rated up to 1,200 A and 5,000 V; can be fitted with up to 20 contacts; designed to eliminate GFI system problems. Duraline WRITE IN NO. 202

Magnetic nail-holding striking cap added to line of interchangeable striking caps offered with Ti-Tech™ titanium hammers; option of milled or smooth striking faces; multi-task hammer easily switches from rough framing to finished carpentry; magnetic cap permits 1-handed nailing in hard-to-reach places; 16 oz. Vaughan & Bushnell Manufacturing Co. WRITE IN NO. 203

Electronic rotation control measures time gap between 2 signals supplied by a proximity sensor reading a revolving or cycling mechanism; when the time gaps exceed set value, device activates; time scale ranging of 0.03 to 512 seconds with adjustable delay allows process to reach operating speed; programmable power supply designed to operate with proximity sensors. Fargo Controls, Inc. WRITE IN NO. 204

Mini-grinder brushes for brushing in confined areas such as corners, cleaning T-connections, stringer bead brush welding, flat surface and edge cleaning, and bevel edge cleaning; available in knotted or crimped wire; mini-grinder cup brushes available in carbon or stainless steel; adaptable to light- and heavy-duty applications; knotted wire model suitable for weld cleaning, scale removal and deburring. Anderson Products WRITE IN NO. 209

Type DX deflection/expansion fittings provide a safe, reliable and effective way to compensate for movement between conduit ends; connect rigid metal conduit and IMC conduit to allow movement up to 3/4 in. or 30% of angular misalignment in any direction; ideal for areas with rotating equipment or heavy vehicle traffic; available in a wide range of sizes; easy to install. OZ/Gedney WRITE IN NO. 210

APS-438 universal air-powered saw and WrapTrack® wraparound track is designed for cutting pipe perfectly square without a heat-affected zone; clamps around the circumference of the pipe for 6 to 60 in. dia.; ± 1/8 in. accuracy; alternative to clamshell-type tools in applications with 13.5 in. clearance; cuts 10 in. sch. 160 pipe in under 10 minutes; 8- or 14-in. fiberglass reinforced abrasive blades and carbide-tipped blades for any pipe. ESCO Tool WRITE IN NO. 211

Complete line of 3-way catalytic mufflers for all Nissan LPG-powered forklift trucks; mufflers are direct fit units that are exact replica of original non-catalytic equipment; reduces installation time and cost; includes built-in 3-way emission control catalyst to eliminate the emissions of carbon monoxide and nitrogen oxides as well as the odor of propane exhaust gases; intended for forklifts used inside to offer higher air quality. Nett Technologies, Inc. WRITE IN NO. 212

Full line of FDA-approved chain and belt guides for use in conveyors; feature oil-filled ultra-high molecular weight polyethylene construction to permit faster operating speeds; fully impregnated with FDA-approved lubricant; can eliminate the need for external lubricant; permits chains to run up to 400 fpm; available in a variety of configurations; 1- or 2-piece curves in 18-30 in. radii and straight wear strips from 2-16 in.; .16 coefficient of friction. Slideways, Inc. WRITE IN NO. 217

Hollow shaft RV-C gear reducer offers a through hole ranging from 31-138 mm; ideal for allowing vacuum lines, wiring harnesses, concentric shafting and cooling lines to be run through the center; extremely high torsional rigidity and overload torque capacity at 500% of rated torque; total lost motion from all sources, including backlash, spring rate and hysteresis, is limited to a maximum of only 1 arc minute. Harmonic Drive Technologies WRITE IN NO. 218

Pre-engineered valve stations are custom configured, water-flow control systems built using proven, reliable components to meet exact project applications; factory assembled, tested and certified by independent agencies to assure flow performance for critical demands; provide uninterrupted water service to hospitals, schools, multi-family dwellings, restaurants, industrial facilities and other applications requiring uninterrupted water supply. Watts Regulator Co. WRITE IN NO. 219

Centerless grinding wheels, rubber regulating wheels and diamond dressing tools featured in a 2-page flyer; classified by through-feed or end-feed centerless applications; application and feature legend classify these 20- and 24-in. conventional abrasive wheels based on application, stock removal, finish and cutting ability; introduces Bonus 21 centerless wheels engineered to provide more usable abrasive and over 25% longer wheel life. Radiac Abrasives, Inc. WRITE IN NO. 220

Brochure features high productivity router cutter optimized for slotting, square shoulder and pocketing operations in aluminum; cutter offers a high metal-removal rate and minimized runout on a master insert; brochure outlines features and covers ordering information, technical illustrations, type of mounting, number of inserts, compatible inserts and full technical guide; information on Combimaster heads and shanks is also included. Carboloy, Inc. WRITE IN NO. 221

Clean design pneumatic valve terminal; ideal for food handling and packaging; designed in accordance with hygienic design standards DIN ISO 14159; products in the clean design program line, including CDVI, have no sharp edges or small radii anywhere; the sub-base of both the main manifold and the expansion modules support up to 4 additional valves; constructed from anodized aluminum; spacing between valves is wide enough to allow easy cleaning. Festo Corp. WRITE IN NO. 222

Third generation of coverall line launched; Posi-Wear3™ offers comfort and job-site durability; ideal for use in demanding industrial environments; super strong, yet thin Posi-Wear3 material is also an ideal choice for workers operating in warmer climates and conditions; fabricated from 3-ply SMS substrate material; good for use in manufacturing, assembly operations, pharmaceutical production and food processing. West Chester Holdings, Inc. WRITE IN NO. 223

Airstik™ window blowoff keeps the window of CNC machines clear of coolant and chips so the part and process remain visible; compact design delivers uniform sheet of air that blows down the surface of the window; operator can make visually informed decisions affecting process for increased productivity; ejects small amount of compressed air through a thin, slotted nozzle; forms laminar sheet of high-velocity air. EXAIR Corp. WRITE IN NO. 224